icnd2 Exam Questions For Cisco 200-105

Make your 200-105 exam  easier and simpler. Our Cisco 200-105 exam practice test software which simulates the real exam testing environment.

Try it Latest DumpsSchool 200-105 Exam dumps. Buy Full File here: https://www.dumpsschool.com/200-105-exam-dumps.html (691 As Dumps)

Download the DumpsSchool 200-105 braindumps from Google Drive: https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view (FREE VERSION!!!)

Question No. 1


To allow or prevent load balancing to network, which of the following commands could be used in R2? (Choose two.)

Answer: B, C



The cost (also called metric) of an interface in OSPF is an indication of the overhead required to send packets across a certain interface. The cost of an interface is inversely proportional to the bandwidth of that interface. A higher bandwidth indicates a lower cost. There is more overhead (higher cost) and time delays involved in crossing a 56k serial line than crossing a 10M ethernet line. The formula used to calculate the cost is:

cost= 10000 0000/bandwith in bps

For example, it will cost 10 EXP8/10 EXP7 = 10 to cross a 10M Ethernet line and will cost 10 EXP8/1544000 =64 to cross a T1 line.

By default, the cost of an interface is calculated based on the bandwidth; you can force the cost of an interface with the ip ospf cost interface subconfiguration mode command.

Question No. 2

Which two pieces of information are provided by the show controllers serial 0 command? (Choose two.)

Answer: A, C

The show controller command provides hardware-related information useful to troubleshoot and diagnose issues with Cisco router interfaces. The Cisco 12000 Series uses a distributed architecture with a central command-line interface (CLI) at the Gigabit Route Processor (GRP) and a local CLI at each line card.

Question No. 3

Which two statements about the PPPoE client physical interface configuration are true? (Choose two.)

Answer: B, D

Question No. 4

The network administrator of the Oregon router adds the following command to the router configuration: ip

route What are the results of adding this command? (Choose two.)

Answer: A, C

Question No. 5

Which command shows your active Telnet connections?

Answer: B

Question No. 6

Refer to the exhibit.

RTA is configured with a basic configuration. The link between the two routers is operational and no routing protocols are configured on either router. The line shown in the exhibit is then added to router RTA. Should interface Fa0/0 on router RTB shut down, what effect will the shutdown have on router RTA?

Answer: A

Static routes remain in the routing table even if the specified gateway becomes unavailable. If the specified gateway becomes unavailable, you need to remove the static route from the routing table manually. However, static routes are removed from the routing table if the specified interface goes down, and are reinstated when the interface comes back up. Therefore the static route will only be removed from the routing table if the S0/0 interface on RTA is shutdown.


Question No. 7

A network administrator would like to implement NAT in the network shown in the graphic to allow inside hosts

to use a private addressing scheme.

Where should NAT be configured?

Answer: A

Question No. 8

Refer to the exhibit.

Which WAN protocol is being used?

Answer: C

“Show interface pos8/0/0” command showing LMI enq sent which show frame-relay encapsulation enabled on this interface.Cisco supports three different Local Management Interface (LMI) types for Frame Relay: Cisco, ANSI Annex D, and Q933-A Annex A


Question No. 9

Which type of topology is required by DMVPN?

Answer: C

Question No. 10

Refer to the graphic.

A company wants to use NAT in the network shown. Which commands will apply the NAT

configuration to the proper interfaces? (Choose two.)

Answer: B, C

Question No. 11

Which two statements about CHAP authentication are true? (Choose two.)

Answer: A, B

Question No. 12

Which PPP subprotocol negotiates authentication options?

Answer: D

A protocol that establishes, configures, and tests data link connections used by the PPP Link Control Protocol offers PPP encapsulation different options, including the following:

Authentication – options includes PAP and CHAP Compression – Data compression increases the throughput on a network link, by reducing the amount of data that must be transmitted. Error Detection -Quality and Magic numbers are used by PPP to ensure a reliable, loop-free data link.

Multilink – Supported in IOS 11.1 and later, multilink is supported on PPP links between Cisco routers. This splits the load for PPP over two or more parallel circuits and is called a bundle.

Question No. 13

What are three components that comprise the SNMP framework? (Choose three.)

Answer: A, B, F

Question No. 14

Which command can you enter to determine whether a voice VLAN has been configured?

Answer: B




Question No. 15

Refer to the exhibit.

Which switch in this configuration becomes the root bridge?

Answer: C

200-105 Dumps Google Drive: (Limited Version!!!)

Related Certification: CCNA Routing & Switching dumps

Facebook Comments